A nice ride up North.
We took Bay Rd to rte 9 in Hadley and met Dan on Damon Road in Northampton by the River. At the end of Damon we went straight on Bridge Road and just kept going.
Nice woods and farm country riding. Small hills.
This brought us past the the Northampton Mountain St Reservoir,then thru Whately and then to the Upper Reservoir.
Up by Conway, we turned right onto rte 116 South. This was hilly and winding and beautiful. Nice riding when you want a little fun on the roads.
We took 116 to South Deerfield and then to Sunderland, where we turned onto rte 47 heading south back to Hadley. This is thru mainly farming community and very spread out. Some winding road, but very minor.
Rte 47 took us back to Bay Road, but not before we parted company with Dan at rte 9.
Overall, from Belchertown and back, it was 64 miles and just over 2 hours.
Event Calendar
Saturday, August 13, 2011
Wednesday, July 20, 2011
Sunday, June 26, 2011
Stafford Springs Motorcycle Swap meet
A very lackluster turnout in Stafford this time. I have never seen such a minimal turnout for the swap meet.
Did see a couple of old Harleys:
And a possible frame for Mark....
Did see a couple of old Harleys:
And a possible frame for Mark....
Sunday, June 19, 2011
On the road again
The bike appears to be running fine, minus my brain fart for wondering why the bike would not start while it was in gear .... duh...
I am now gassed up and ready to go:
I am now gassed up and ready to go:
Day 14 and Day 15- Kawi engine startup preparations and startup
Well, I took the final key steps to starting the bike on Saturday. I made the remain electrical connections, bled the clutch and put on the tank. I also took the time to put on the new exhaust. This required scrounging for some rubber grommets and fasteners at Autozone to connect the exhaust in a position behind the passenger peg. [There's a couple more hours.]
Today, I hooked up the battery and rolled the motor a few times to get the oil circulating. Then I connected the spark plugs and she fired right up.
Then my wife says 'hey, what is that bolt that just fell on the floor under the bike'. My heart went THUMP, THUMP, THUMP.
I turned the bike off and said oh-crap, because it looked like a rocker cover bolt... Turned out, it was just the bolt for the one shift pedal I had loosely slipped on. Thank God. I started the bike back up and let the motor heat up until the fan came on. I have not yet heard any ticking noises from the motor. Hopefully it will stay that way.
The new exhaust has a slightly higher pitch then the duals... and there a little louder.
Test ride this afternoon.
Today, I hooked up the battery and rolled the motor a few times to get the oil circulating. Then I connected the spark plugs and she fired right up.
Then my wife says 'hey, what is that bolt that just fell on the floor under the bike'. My heart went THUMP, THUMP, THUMP.
I turned the bike off and said oh-crap, because it looked like a rocker cover bolt... Turned out, it was just the bolt for the one shift pedal I had loosely slipped on. Thank God. I started the bike back up and let the motor heat up until the fan came on. I have not yet heard any ticking noises from the motor. Hopefully it will stay that way.
The new exhaust has a slightly higher pitch then the duals... and there a little louder.
Test ride this afternoon.
Monday, June 13, 2011
Day 12 and Day 13 of the Kawi engine installation
So, I am nearing the end ( I hope ) of this project.
On Day 12, I did the initial connections of the engine to the bike. This entailed doing some of the tougher connections that could be done with the engine nearly in place but not quite, so I had room to work.
First, I started connecting up the throttle body.... throttle connections, vacuum hoses, etc
and connecting up the water lines.
Then connect up the transmission.
Then attach the motor mounts.
Another hour working on the bike.
Then I start Day 13 and connecting almost everything.
The thottle ...
The lower frame.
Lower electrical connections....
The horns ...
The switch and choke ...
air cleaner backing plates
The radiator ..
And now I am so close. I need to bleed the clutch before I can close up the left side, and I have a couple of lines for the gas tank and then I can put on the tank and put in the fluids.
And that is a 2 more hours down. At some point I will add these hours all up for the job.
On Day 12, I did the initial connections of the engine to the bike. This entailed doing some of the tougher connections that could be done with the engine nearly in place but not quite, so I had room to work.
First, I started connecting up the throttle body.... throttle connections, vacuum hoses, etc
and connecting up the water lines.
Then connect up the transmission.
Then attach the motor mounts.
Another hour working on the bike.
Then I start Day 13 and connecting almost everything.
The thottle ...
The lower frame.
Lower electrical connections....
The horns ...
The switch and choke ...
air cleaner backing plates
The radiator ..
And now I am so close. I need to bleed the clutch before I can close up the left side, and I have a couple of lines for the gas tank and then I can put on the tank and put in the fluids.
And that is a 2 more hours down. At some point I will add these hours all up for the job.
Saturday, June 11, 2011
Day 11 - Kawi engine installation begins
I went out to the garage for an hour and raised the rear of the bike a couple inches so that the rear tire was definitely off the floor and I had some room to work with the motor.
Then I rearranged the motor on the lift so that none of my blocking would be in the way and removed the oil filter. Then I slid the motor mostly in place and did a little blocking to help keep it there for the next phase of starting the throttle connections.
Then I rearranged the motor on the lift so that none of my blocking would be in the way and removed the oil filter. Then I slid the motor mostly in place and did a little blocking to help keep it there for the next phase of starting the throttle connections.
Subscribe to:
Posts (Atom)




































